How to Use Straight Line and Inclined Line both in Single Drawing? In this way, you can make a Rectangle or any object with a line command. Step 9: Press Enter to exit from command. Step 8: You can choose the close option from the lower-left corner of the workspace to close the object. Step 7: Give direction in the vertical position in the down word direction and give the length of 40 mm. Step 6: Then give direction in the horizontal position in the left direction and length of 60 mm, then press Enter key. ![]() Step 5: Again, I will give direction in the vertical position and give the length of 40 mm, then press Enter key. Step 4: Now, I will drag my cursor in the right direction and give the length of 60 mm – press Enter key. Step 3: Turn Ortho On for a straight line. I will show it to you by creating a Rectangle by using the line command. Give another direction, then again give length, and press Enter key. Step 3: Give direction in which you want to draw a line, give length, then press Enter key. Step 1: For creating an object, take a line command. You can easily make an object my use line command after learning the line command thoroughly. The further examples illustrate on creating an object by line command. You can continue your line as many as the time you want. Step 6: Give inclination angle 150, then press Enter to apply this command. Step 5: I will show you how to continue your line. If you want to continue the line in other direction and inclination, then don’t exit from line command just again give the length of line and inclination angle by following the same steps as we did previously. Step 4: Press tab to give the angle of inclination and type 30 as angle, then press Enter to apply the command, and again press Enter to exit. Step 2: I will make sure that my Ortho is in Ortho off mode. Step 1: Give the first point in my workspace. Step 6: Again, press Enter or Esc to leave the command. Step 5: Press the tab and give the inclination angle, and press Enter key. Step 3: Make sure Ortho is in ‘Ortho off’ mode for putting it off, press the F8 key. For drawing an inclined line, take a line command from the draw tool. You can easily draw it by giving the inclination angle. Let’s understand this method with a few examples: Example #1ĭrawing an inclined line in AutoCAD is not hard work. Snapping makes drawing easy in AutoCAD software. center point of the line, endpoint of the line, etc. ![]() These dots are snapping points of that line or object, i.e. The selection will show in blue color with some dots. Step 7: You can select any line or object by clicking on it. ![]() Step 6: Now, I will drag the mouse in the right direction and give the length of 40 mm by typing it from the keyboard and will click Ok to apply my command and press Enter to exit. Step 5: Take the point anywhere in the workspace, turn Ortho On by pressing the F8 key. Step 4: Here, I will show it by example I will take the line command from the draw tool. To exit any command, just press Enter or Esc button on the keyboard. Step 3: Give the direction, give length, then click OK or simply press Enter from the keyboard. Vertical Xline will be invoked.Ĥ) I will bisect all the points from the plan which I want to show in the Elevation.Step 2: Turn Ortho On for creating your line straight for turning Ortho On, you can press F8 or click on Ortho On option as shown in the below image. Example of Construction line Command in AutoCADġ) For example, I want to draw Elevation from the plan.Ģ) So, I will select the Xline command from the draw panel dropdown menu as shown, or by typing ‘ XLINE’ in the command bar.ģ) Then I will press the ‘ V’ key to drawing vertical lines of Elevation. ![]() By typing ‘ H’ Enter or ‘ V’ Enter, we can directly draw horizontal or vertical lines.ħ) after selecting the ‘ bisect’ option, we can draw a bisection line by selecting points.Ĩ) By selecting the ‘ offset’ option from the command bar, we can take the offset of the lines. This command is mainly very useful for drawing Elevation of any drawn plan.Ģ) This command creates a line of infinite length.ģ) It can use to construct a line or reference line for trimming boundaries.Ĥ) We can invoke the X line command by selecting this command from the draw panel drop-down menu and selecting Horizontal or vertical or bisect or offset from the command bar.ĥ) By selecting the Horizontal or vertical options we can draw horizontal or vertical lines by clicking on the point from which you want to draw lines.Ħ) Or type ‘ XLINE’ in the command bar and press Enter it will be invoked. Construction line (X-LINE) Command Draw panelġ) A Construction is also called ‘X lines’.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |